

The Grundfos JP 4-54 PM START 93294164 is an automatic pressure boosting system consisting of a single-stage self-priming centrifugal jet pump and a Grundfos PM START electronic controller. It is designed to increase pressure and provide automatic water supply in homes, country houses, gardens, and other domestic applications, using clean water, potable water, or rainwater within the conditions specified by Grundfos.
The set combines a robust pump with a stainless steel housing and an electronic pressure manager that performs automatic start and stop according to water demand. The PM START on this model is configured with a start pressure of 1.5 bar and keeps the pump running while it detects water flow. It also includes dry-run protection and an integrated non-return valve, reducing the risk of damage when there is no water at the suction side.
The JP 4-54 PM START is designed to automate water supply without the need to manually switch the pump on and off. When a tap, valve, or point of use is opened and the system pressure drops to the start level, the PM START automatically activates the pump.
As long as water is flowing, the pump continues to operate. When the demand is closed and flow stops, the controller automatically stops the unit.
This operation makes the set suitable as a pressure boosting system for domestic installations, supply from tanks, rainwater harvesting, and irrigation applications.
Reference 93294164 uses a PM START controller configured with a 1.5 bar start pressure.
Pressure control Specification Controller Grundfos PM START Start pressure 1.5 bar Automatic start Yes Automatic stop Yes, when flow stops Dry-run protection Yes Non-return valve IntegratedThe PM START is a start/stop controller and not a variable speed drive. The pump runs at fixed speed, so the available pressure varies depending on the flow rate and the operating point of the installation.
One of the most notable features of the Grundfos JP range is its self-priming capability. Once correctly commissioned and initially primed, the pump can draw water from a level below its inlet connection.
The pump is designed to temporarily handle a mixture of air and water during the priming process until stable pumping conditions are reached.
Grundfos specifies a maximum suction lift of up to 8 m, including suction pipe head losses and under the conditions defined by the manufacturer.
The suction capability makes it possible to use the JP 4-54 PM START with water sources located below the pump level.
Possible supply sources include:
The actual vertical distance achievable also depends on pipe length and diameter, installed fittings, water temperature, suction tightness, and head losses.
The JP 4-54 range is sized to provide a flow rate of up to 4 m³/h. This capacity makes it suitable for different domestic water points and irrigation applications within the pump performance curve.
Hydraulic performance Value Reference maximum flow rate 4 m³/h Maximum head 54 m Maximum suction lift 8 m Maximum system pressure 6 barMaximum flow and maximum head are not achieved simultaneously. The actual operating point results from the intersection between the pump curve and the hydraulic resistance of the installation.
The designation JP 4-54 refers to a pump with a reference maximum head of approximately 54 m of water column.
This capability makes it possible to significantly increase the available pressure in installations where the supply network is insufficient or where water comes from a tank located at a lower level.
The effective pressure at each point of use will depend on the static head, required flow, pipe length and diameter, and losses caused by valves, filters, and accessories.
The PM START controller includes dry-run protection. This function monitors the presence of pressure and flow during operation and stops the pump when it detects a situation compatible with lack of water.
Dry running can cause accelerated wear of the mechanical seal and other hydraulic components. The integrated protection helps reduce the risk of damage and the maintenance or repair costs associated with it.
During the initial priming process, if the controller does not detect pressure or flow within the expected interval, it triggers a dry-run alarm.
The PM START includes a non-return valve that prevents reverse water flow through the controller when the pump stops.
This function contributes to the correct operation of the automatic system and simplifies installation by integrating one of the usual components of a pressure boosting installation.
It may also be advisable to install an additional foot valve with strainer on the suction line, especially when drawing from a tank or well, following Grundfos installation recommendations.
The electronic manager provides visual indication of system status to facilitate monitoring and diagnosis.
This information makes it easier to identify issues such as lack of water during priming or operation.
The current configuration associated with reference 93294164 uses a high-efficiency single-phase motor with useful power P2 of 0.75 kW.
Electrical data Specification Power supply 1 × 220-240 V Frequency 50 Hz Power input P1 1,020 W Useful power P2 0.75 kW Rated current 4.5 A Rated speed Approx. 2,840 rpm Efficiency class IE2 Insulation class FThe single-phase motor includes thermal protection. In the event of overheating, the system protects the motor by stopping operation.
The motor is air-cooled and uses sealed, lifetime-lubricated ball bearings, designed to provide a long service life and reduce maintenance requirements.
The pump hydraulic housing is made of stainless steel EN 1.4301 / AISI 304, providing good corrosion resistance in clean water supply applications.
The robust construction of the JP range is especially suited to equipment that must operate for long periods in domestic and garden installations.
The impeller is made of glass-fiber reinforced PPO composite material. This solution provides mechanical strength, low weight, and suitable performance in continuous contact with water.
Component Material Pump housing Stainless steel EN 1.4301 / AISI 304 Impeller Reinforced PPO composite Pressure Manager components Reinforced polyamide and technical water-compatible materials Controller diaphragm EPDMThe suction and discharge hydraulic connections use G1 thread, simplifying integration of the system into standard domestic installations.
Connection Size Suction G1 Discharge G1 Connection standard ISO 228-1 Nominal pressure PN 6To achieve maximum performance, it is especially important to correctly size the suction pipe and minimize head losses, air ingress, and unnecessary restrictions.
Reference 93294164 corresponds specifically to the European version with a power cable of approximately 1.5 m and Schuko plug.
This makes electrical connection easier in installations prepared with a suitable and properly protected outlet.
The pump has an IP44 protection rating. The unit must be installed in accordance with the manufacturer’s instructions regarding humidity, ventilation, and environmental exposure.
The PM START electronic module has its own enclosure protection and must be kept properly closed after any intervention to maintain the specified protection rating.
The maximum working pressure indicated for the hydraulic system is 6 bar.
The complete installation must be designed so that pipes, valves, accessories, and connected equipment are compatible with the pressures that may be reached during operation.
The JP range is designed to pump clean, low-viscosity, non-aggressive, non-toxic, and non-explosive liquids without solid particles or fibers.
Typical applications include:
It is not designed for wastewater, liquids with solids, dirty water, aggressive chemicals, or flammable liquids.
For continuous S1 operation, Grundfos specifies a maximum liquid temperature of approximately 40 °C. The manufacturer allows higher temperatures under certain intermittent operating conditions, but for typical domestic supply applications the range corresponding to continuous duty should be respected.
Condition Reference value Liquid temperature in continuous duty Up to 40 °C Ambient temperature in continuous duty 0 to 40 °C Maximum relative humidity 98%Grundfos specifies a maximum frequency of approximately 20 starts and stops per hour.
In installations with small and frequent water demands, it may be advisable to add a compatible external pressure tank. The tank provides a small water reserve and can reduce the number of pump start cycles.
The JP 4-54 PM START is supplied as a system with an electronic controller and does not include a pressure accumulator tank.
Grundfos allows the installation of an external tank when the aim is to reduce the frequency of starts and stops, especially in installations with small losses or repetitive low-volume demands.
This distinguishes the JP PM START version from JP PT sets, which include a pressure tank as part of the system.
The unit maintains a relatively compact format to facilitate installation in technical rooms, garages, and other service areas.
Reference dimension Approximate value Length 424 mm Width 186 mm Height of the set with pressure manager Approx. 380 mmThe dimensions should be checked together with the additional space required for piping, hydraulic connections, motor ventilation, and maintenance operations.
The system is especially suitable for domestic and garden applications that need pressure boosting or water pumping from an independent source.
When the pressure available from the network or tank is insufficient, the JP 4-54 PM START can be used to supply different points of use with higher pressure.
Dimensioning should take into account the number of points that may operate simultaneously, the required flow rate, and the pressure needed at the most unfavorable point.
Thanks to its self-priming capability and automatic operation, the system is suitable for domestic rainwater harvesting installations stored in tanks.
The water must be properly filtered and free of solid particles or fibers to protect the hydraulic components.
The flow rate of up to 4 m³/h and the high available head make the JP 4-54 PM START suitable for domestic irrigation systems, provided that the number and characteristics of the emitters are within the pump performance curve.
It can supply hoses, sprinklers, and certain irrigation systems, after checking the required flow and pressure.
When the pump draws from a tank located at a lower level, special attention must be paid to the suction pipe. It must be airtight and correctly sized to avoid air ingress and excessive head losses.
Grundfos recommends installation configurations that may include a foot valve and strainer on the suction side, especially when working with wells or tanks.
The JP 4-54 PM START is a surface pump. The unit must not be placed in water.
The pump is installed in a suitable location and draws water through a pipe connected to its inlet. For installations where the pump must remain submerged, a specific submersible pump should be selected.
The product operates on single-phase 220-240 V, 50 Hz power supply. The installation must have an earth connection and the electrical protections required by current regulations.
Grundfos instructions require protection against indirect contact and specify the use of a residual current device with a tripping current below 30 mA within the conditions indicated for the installation.
A standard Grundfos JP pump is a self-priming pump that requires an external system to control automatic start and stop.
The JP PM START version adds the electronic pressure manager from the factory, resulting in a set ready to operate automatically according to demand.
Function JP JP PM START Self-priming pump Yes Yes Automatic start/stop Requires external control Yes Dry-run protection No with the basic pump Yes, via PM START Non-return valve in controller No Yes Alarm indicator No YesThe Grundfos JP 4-54 PM START 93294164 is a compact solution for automatically increasing water pressure in homes, gardens, and rainwater harvesting systems. Its self-priming pump, flow rate of up to 4 m³/h, maximum head of 54 m, suction up to 8 m, PM START controller with 1.5 bar start pressure, dry-run protection, non-return valve, and stainless steel housing make it possible to create a reliable and easy-to-install water supply system for domestic clean water applications.