Samsung EHS 16 kW Monobloc Air Source Heat Pump R290 - Three Phase

The Samsung EHS Mono R290 16 kW Three-Phase is a high-power monobloc air source heat pump designed to meet high thermal demands in large homes and light commercial applications, integrating heating, cooling, and domestic hot water production in a single outdoor unit.

It uses natural refrigerant R290 (GWP = 3), which has a very low climate impact and complies with European F-gas regulations. Its monobloc architecture integrates the refrigeration circuit within the outdoor unit, simplifying the indoor hydraulic installation.

High Temperature for Renovation Projects

Especially suitable for replacing boilers in systems with conventional radiators or emitters that require high supply temperatures.

• Heating outlet temperature: 15–75 ºC.
• Domestic hot water: up to 70 ºC with outdoor temperatures down to -10 ºC without electric backup (depending on conditions).
• Enlarged heat exchanger (up to +39.6% surface area) for optimized thermal transfer.
• Reinforced compressor with higher compression ratio, designed to operate at high pressures with greater efficiency and reliability.

Power and Stability in Demanding Conditions

• Heating capacity (A7/W35): 16.0 kW.
• Cooling capacity (A35/W18): 14.0 kW.
• Heating operating range: -25~35 ºC.
• Cooling operating range: 10~46 ºC.

Quiet Operation

• Sound pressure (normal mode): 51 dB(A).
• 4-step silent mode: down to 35 dB(A).
• Double-layer acoustic insulation and optimized grille design to reduce compressor noise and vibration.

Robust Design and Dimensions

Higher power versions feature an optimized chassis to maximize heat exchange and structural stability, while maintaining an elegant dark gray finish.

• Net dimensions (W x H x D): 1270 x 1018 x 530 mm.

R290-Specific Safety Features

• Optimized piping layout to minimize leak risk.
• Pressure sensor for refrigerant detection in the water circuit.
• Forced fan mode and air separator in the outlet pipe in case of incident.
• Potential ignition sources are sealed and located at the top of the unit.

Professional Installation and Maintenance

Quick access to internal components via a removable side panel with three screws, reducing service times. Requires three-phase power supply for proper connection.

Advanced Connectivity and Control

• SmartThings Energy: real-time energy consumption monitoring and activation of energy-saving modes.
• EHS Cloud Service: remote diagnostics with access to error reports, equipment status, and technical data for professionals.

Indicative Coverage by Thermal Load

The climate-controlled area depends on the actual thermal load of the building. Reference values (load calculation required):

• 30–40 W/m²: approx. 400–530 m² (well insulated)
• 50–60 W/m²: approx. 265–320 m² (average insulation)
• 80–100 W/m²: approx. 160–200 m² (poor insulation)

Note: Indicative values; always confirm with a thermal study of the project.

Technical Specifications (AE160CXYDGK/EU)

• Heating capacity (A7/W35): 16.0 kW
• Cooling capacity (A35/W18): 14.0 kW
• Water outlet temperature (heating): 15–75 ºC
• Water outlet temperature (cooling): 5–25 ºC
• Sound pressure (Normal): 51 dB(A)
• Sound pressure (Silent Mode): 35 dB(A)
• Operating temperature range (heating): -25~35 ºC
• Operating temperature range (cooling): 10~46 ºC
• Power supply: 3Ф, 4 wires, 380~415 V, 50 Hz
• Refrigerant: R290 (GWP = 3)
• Hydraulic connections inlet/outlet: 1" BSPP male / 1" BSPP male
• Net dimensions (W x H x D): 1270 x 1018 x 530 mm

Installation Considerations

• Monobloc unit for outdoor installation with hydraulic connections to the interior.
• Requires three-phase power supply 380~415 V, 50 Hz.
• Observe minimum service and ventilation distances as indicated by the manufacturer.