Samsung EHS 16 kW Monobloc Air Source Heat Pump R290 - Single Phase

The Samsung EHS Mono R290 16 kW Monophase is a high-capacity air source heat pump designed to meet high thermal demands in large homes and small commercial spaces, providing heating, cooling, and domestic hot water production with a single outdoor unit.

It features natural refrigerant R290 (GWP = 3), which has a very low climate impact and complies with evolving European regulations on fluorinated gases. Its monobloc architecture houses the refrigeration circuit in the outdoor unit, simplifying the indoor hydraulic installation.

High Temperature for Renovation and Radiators

Especially suitable for replacing boilers in installations with conventional radiators that require high supply temperatures.

• Heating output temperature: 15–75 ºC.
• Domestic hot water: up to 70 ºC with outdoor temperatures as low as -10 ºC without electric backup (depending on conditions).
• Enlarged heat exchanger (up to +39.6% surface area) for improved thermal exchange.
• Reinforced compressor with higher compression ratio, optimized for high-pressure operation with greater efficiency and reliability.

Power and Stability in Demanding Conditions

• Heating capacity (A7/W35): 16.0 kW.
• Cooling capacity (A35/W18): 14.0 kW.
• Heating operating range: -25~35 ºC.
• Cooling operating range: 10~46 ºC.

Quiet Operation

• Sound pressure (normal mode): 51 dB(A).
• 4-step silent mode: down to 35 dB(A).
• Double-layer acoustic insulation and patented grille design to reduce compressor noise and vibrations.

Robust Design and Dimensions

Higher power versions feature an optimized chassis for thermal exchange and structural stability, maintaining a discreet dark gray aesthetic.

• Net dimensions (W x H x D): 1270 x 1018 x 530 mm.

Safety Adapted for R290 Use

• Optimized piping design to minimize stress and risk of leaks.
• Pressure sensor for refrigerant detection in the water circuit.
• Forced fan mode and air separator in the outlet pipe in case of leakage.
• Potential ignition sources are sealed and located at the top of the unit.

Efficient Installation and Maintenance

Removable side panel with three screws for quick access to internal components, reducing installation and maintenance times during technical interventions.

Advanced Connectivity and Control

• SmartThings Energy: real-time consumption monitoring and activation of energy-saving modes.
• EHS Cloud Service: remote diagnostics for professionals with access to equipment status, error logs, and technical data.

Indicative Coverage by Thermal Load

The heatable area depends on the building’s actual thermal load. As a general reference (always confirm with a load calculation):

• 30–40 W/m²: approx. 400–530 m² (well insulated)
• 50–60 W/m²: approx. 265–320 m² (average insulation)
• 80–100 W/m²: approx. 160–200 m² (poor insulation)

Note: Indicative values; always carry out a thermal study of the project for correct sizing.

Technical Specifications (AE160CXYDEK/EU)

• Heating capacity (A7/W35): 16.0 kW
• Cooling capacity (A35/W18): 14.0 kW
• Water outlet temperature (heating): 15–75 ºC
• Water outlet temperature (cooling): 5–25 ºC
• Sound pressure (Normal): 51 dB(A)
• Sound pressure (Silent Mode): 35 dB(A)
• Operating temperature range (heating): -25~35 ºC
• Operating temperature range (cooling): 10~46 ºC
• Power supply: 1Ph, 2 pipes, 220~240 V, 50 Hz
• Refrigerant: R290 (GWP = 3)
• Hydraulic connections inlet/outlet: 1" BSPP male / 1" BSPP male
• Net dimensions (W x H x D): 1270 x 1018 x 530 mm

Installation Considerations

• Monobloc unit for outdoor installation with hydraulic connections to the indoor system.
• Observe minimum service and ventilation distances as per the technical manual.
• Requires configuration to enable connectivity and cloud service functions.